Squirrel Stopper

This all-steel bird feeder hanger pole allows you to feed wild birds, not squirrels. Unique baffle wiggles and moves in all directions to ensure that it is virtually impossible for squirrels to climb up and access seed. You can display up to eight wild bird feeders or hanging plants at once. Each 2" diameter arm holds up to two feeders and 15 pounds! Steel auger twists securely into the ground and holds the Squirrel Stopper firmly in place. Rust-resistant powder-coated steel construction resists squirrel and weather damage. No-tool assembly makes this wild bird feeder hanger easy to put together. Includes interchangeable cardinal or finial topper for a subtle, decorative touch. To clean, simply wipe with a damp cloth. 1-year limited warranty. Black. Squirrel Stopper measures 36" x 118" high overall.

Please click on "More Information" for assembly and care instructions.

WARNINGS - Pieces are made of metal and are heavy and may have sharp or rough edges. Handle with care. Keep fingers clear when adjoining sections. When screwing auger into the ground, keep clear of electrical or water lines. Securely attach all pieces of the Squirrel Stopper, and check regularly to assure that none are loose. Do not climb erected Squirrel Stopper apparatus or use as support. Attach bird feeders securely to eyelets on completed unit, and check regularly to assure that they remain secure. Regularly check and tighten all exposed attachments on the apparatus. Do not place hands underneath the shroud, as springs are present. Do not twist or pull on the shroud, as this may deform the springs. This will void the warranty. WEIGHT LIMIT for each of the four hangers is 15 lbs. (60 lbs. total for all four hangers).

INSTALLATION AND ASSEMBLY- Squirrels have great leaping ability. Therefore, do not install this unit within 10 feet of trees, fences, house roof, or any other overhang or elevated platform.

Step 1. Insert top of auger into bottom of the lower section of the vertical post. Secure with thumbnut and bolt.

Step 2. Carefully insert one of the 1" diameter horizontal bars through the two corresponding holes in the lower section of the vertical post so that it is centered. Place auger point at desired location on the ground, and begin to screw auger clockwise into the ground to a point 18"- 24" above the auger (indicated on lower post section). Bar will be suitable to screw auger into most soils. If soil provides very firm resistance, or you feel that horizontal bar is going to bend, loosen soil with pick-ax or shovel, and/or use another device (broom handle, solid metal rod, etc.) to screw post in. Use level to assure that post is plumb.

Step 3. Line up bump on the inside surface of the lower rim of the middle section of the vertical post (with shroud attached) with the groove on the outside surface of the upper sleeve of the lower section of the vertical post. Lower the middle section until it stops , then twist it clockwise to secure it. Do not twist or pull on the shroud, as this may deform the springs.*

Step 4. Note rubber grommets lining cross tube holes in upper post segment. Lubricate these rubber grommets with water, which will allow easy insertion of 1" diameter horizontal bird feeder support bars through the appropriate sets of holes . Slide bars in until centered.

Step 5. Install support brackets . Place bracket against 2" central post and 1" bird feeder support crossbar. Secure to crossbar with eyelet screw (eyelet should be on the bottom), lock washer, and thumb nut. Repeat this procedure with bracket on the opposite side of the central post. Secure the bottom of the bracket by running the bracket screw through the bottom hole on one bracket, then through the central post, then through the bottom hole of the opposite bracket. Secure with thumb screw. Next: Repeat this procedure with the two support brackets which connect to the other crossbar.

Step 6. Line up bump on the inside of the lower rim of the upper section of the vertical post with the groove on the outside surface of the upper sleeve of the middle section of the vertical post. Lower the upper section until it stops , then gently twist it clockwise to secure it.

Step 7. Place birdfeeder eyelet screws (4) into holes at both ends of the two horizontal birdfeeder support bars. Eyelets should be at the bottom. Secure with lock washers and thumbnuts on the topside of the bars.

Step 8. Place decorative top holder over the top of the upper section of the vertical post. Secure with thumbscrew. Center decorative top in slot on top of the decorative top holder. Secure with thumbscrew.

* At regular intervals, CHECK AND TIGHTEN (IF NECESSARY) ALL SCREWS AND ATTACHMENTS. If spring(s) becomes unattached for any reason, carefully remove 3 screws (with Phillips-head screw driver) and remove shroud cover. Re-attach spring(s) to proper attachments and reattach shroud cover.

NOTE: When inserting horizontal bars, lubricate the rubber grommets with water. Hang objects of approximately equal weight on both ends of the horizontal bars. This will place less stress on the bars and brackets.

We're sorry!

No testimonials have been submitted for this product.

Would you like to submit a testimonial? Click here